Products Description
The process involves blending various types of commonly used battery powders and liquids to achieve a uniformly mixed battery slurry. This method is particularly well-suited for high-viscosity applications.
Technical Parameters
| Main parameters： | |
| Model | XW-XFZH05 |
| Lower Barrel Parts | |
| Design total volume | 8L |
| Elective volume | 2.7-5L |
| Container inner diameter | 240mm |
| Container inside depth | 180mm |
| Container material | The parts in connect with materials is 304 stainless steel |
| Tempering jacket form | The bottom and the barrel jacket can input water for cooling, heat preservation and heating |
| Tempering jacket port | G3/4″，with quick opening movable joint， |
| jacket withstand pressure≤0.4MPa | |
| Tempering jacket circulation system | prepared by customer， |
| jacket water inlet temperature≤8℃， | |
| cooling water flow＞3.5L/min | |
| Discharge materials form | bottom of a G1-1/2″ three-piece discharge ball valve, equipped with 2 “standard ISO quick connect clamp connector |
| Design environment temperature | -10～+120°C |
| Move mode | Casters move |
| Mixing Parts | |
| Working frequency | 5-50hz |
| Mixing power | 1.5kw |
| Mixing blade speed | 10-98rpm |
| Planetary box rotate speed | 5-50rpm |
| Mixing blade diameter | 124mm |
| Mixing blade model | Variable cross-section spiral twist type, 90 ° helix |
| Mixing blade material | 304 stainless steel |
| Mixing blade line speed | 0.06-0.6m/s |
| Mixing blade number | 2pcs |
| Dispersing Parts | |
| Working frequency | 5-50hz |
| Dispersing power | 2.2kw |
| Dispersing rotate speed | 610-6100rpm |
| Dispersing plate diameter | 70mm |
| Dispersing model | Serrated |
| Dispersing plate material | 304 stainless steel |
| Dispersing line speed | 2.2-22m/s |
| Dispersing number | 1pcs |
| Dispersing shaft number | 1pcs |
| Scratch the Wall Parts | Scratch wall bracket material：304 stainless steel |
| Scratch wall material：Teflon | |
| Scratch wall rotate speed：Consistent with planetary box rotate speed | |
| Removable or not：Removable design (Need to remove when scraping the wall on high viscosity process) | |
| Base and Lifting Parts | Parts materials：High rigidity structural carbon steel |
| Lifting way：electric | |
| Lifting guide：High-precision linear guide | |
| Lifting itinerary：≤290mm | |
| Upper Barrel Parts | Upper barrel material：304 stainless steel |
| Power feed port：quick opening interface DN40 1pcs | |
| Liquid feed port：ISO standard 1/2″ quick interface 1pcs | |
| Mirror port：DN50 tempered glass sight glass 1pcs | |
| Vacuumize port：G1/2 ” 1pcs | |
| Exhaust port：together with vacuumize port | |
| Digital vacuum gauge port：M14×1.5 Internal thread metric tooth interface 1pcs | |
| Control System | Electrical cabinet：Used to install low-voltage electrical components such as inverter |
| Manual operation panel：For placement buttons, knobs, gauges etc | |
| Power supply：AC 3×380V±5﹪，50Hz | |
| Control mode：electronic control | |
| Power control and speed adjustment mode: Inverter start and control | |
| Cooling mode：Air-cooled (wind cooling) | |
| Operation mode：Touch screen | |
| Digital temperature display gauge：material temperature | |
| Emergency stop button：1pcs | |
| Alarm system：Over-temperature alarm, over-temperature alarm shutdown, alarm shutdown | |
| Speed display: Touch screen shows the speed | |
| Power instructions: 1pcs | |
| Safety Chain System | Emergency stop: press the emergency stop switch, the device immediately stop, and can not do anything |
| Start low-speed mixing: can lift the barrel and turning at the same time | |
| High-speed dispersion: barrel up in place before turning | |
| Safe lock in operation: When the machine is running, the mixing barrel can not be lowered, can not open the mixing barrel. | |
| Prevent vacuum tube backflow: special vacuum buffer tank design, can effectively prevent the vacuum pump oil back to the mixing drum phenomenon | |
| Stop running fault: Inverter comes with overload, overcurrent, overvoltage, leakage, lack of equal protection | |
| Mixing barrel lift: stirring barrel in place to rise | |
| Mixing barrel did not return to normal pressure can not be dropped. | |
| After mixing barrel rises in place and high-speed dispersion, then can be started. | |
| After mixing barrel rises in place, with locking protection system, to prevent while the mixing barrel rises to high place abnormal fall. | |
| Dry mixing stage, while the barrel rising, the stirring paddle need to rotate at the same time. | |
| Other description | Temperature probe：Pt100 |
| Temperature measurement: Located of the barrel wall to detection of internal material temperature | |
| Transmission parts bearings：High-speed components for imported bearings, low-speed components for domestic bearings | |
| Oil seal：Domestic brands，O-ring for Static seal，dynamic seal using mechanical seals or skeleton oil seal | |
| Grease：Domestic brands | |
| Mechanical seal lubricants：Imported brand | |
| Petrol cylinder：Domestic brands | |
| Petrol station：Domestic brands | |
| Valve：Domestic brands | |
| acuum design quantity demand：vacuum system prepared by customer own, air exhaust volume 2L/S（2X-2） | |
| Vacuum hold：-0.098Mpa，holding pressure for 24 hours＞-0.085Mpa，do not leak to the barrel | |
| Total host power：＞4kw | |
| Total weight: about 700kg | |
| Dimensions：L1463mm×W610mm×H1770mm | |
| Appearance color：off-white | |
| Ground bearing：900kg/㎡ | |
